Subject: From: Date:

Re: [ECS] "Missed" DIGITAL-INPUT-K changes ? Warren Hughes - SolNet Ltd Wed, 17 Jan 2001 08:59:56 +1300

Wed, 17 Jan 2001 08:59:56 +1300

---

Hi Doug, yes I found out the voltage and are still using pins 2+3, yes I
have the supplied resistor in place; its between the I/O point and the
common. Yes the PIR is a N/C type. Yes the meter goes to 0 when motion
is detected; its almost as if there is an issue with the comms between
the SECU-16 and the Ocelot...I havent been able to get much (any) help
out of AppDig.

Just to confirm the comms from the SECU-16 to the Ocelot is A -> A, B ->
B ?

Cheers, Warren

Doug Storey wrote:
> 
> Warren;
> Supervised digital input IS jumper on pins 2 and 3. If you use a Multi-meter
> you can see that with the jumper on 2 and 3 there is an output voltage. If
> the Jumper is on 1 and 2 there is none. Don't mean to be insulting but do
> you have the 1K resistor in place?
> When you place a meter on the PIR does the meter go to 0 when detecting
> motion?
> Is this a Normally Closed circuit ? ( A potential customer is reporting such
> a problem  with a PIR that opens the contact "briefly". )
> 
> -----Original Message-----
> From: Warren.Hughes@newzealand.sun.com
> [mailto:Warren.Hughes@newzealand.sun.com]
> Sent: Sunday, January 14, 2001 2:15 PM
> To: ecs-list@netbloc.com
> Subject: Re: [ECS] "Missed" DIGITAL-INPUT-K changes ?
> 
> Hi Chaps, guess what, I emailed Applied Digital and this is the result:
> ----
> Place the pins on 2 and 3. I'm still working on it.
> 
> Kevin Barrett
> Have a great day
> ----
> 
> The above doesnt work at all; I am sure its meant to be 1+2.
> 
> I wonder if my SECU-16 to Ocelot to PC communication is just not fast
> enough, has anyone had lag problems like this?
> 
> Cheers, Warren
> 
> Doug Storey wrote:
> >
> > No,  It is a jumper. The SECU-16 Manual has conflicting data on how to set
> > the jumper in section 3.1. I think Warren Hughes was going to contact
> > Applied Digital
> >
> > -----Original Message-----
> > From: Mark Gilmore [mailto:omnip@usit.net]
> > Sent: Friday, January 12, 2001 8:06 AM
> > To: ecs-list@netbloc.com
> > Subject: Re: [ECS] "Missed" DIGITAL-INPUT-K changes ?
> >
> > Hi Doug,
> > Was this a change you had to make from a CMAX setup default ?
> > Is this something I need to doc in ECS.HTM ?
> > Thanks,
> > --
> > Mark Gilmore
> > Omnipotence (ECS home automation software)
> > http://omnipotencesoftware.com
> > 423-745-0026
> > Hours: Mon-Sat, 9AM-8PM/EST
> >
> > Doug Storey wrote:
> > >
> > > Yes but the problem was that I was using the 4-20ma input setting rather
> > > than supervised.
> > >
> > > -----Original Message-----
> > > From: Mark Gilmore [mailto:omnip@usit.net]
> > > Sent: Sunday, January 07, 2001 3:34 PM
> > > To: ecs-list@netbloc.com
> > > Subject: [ECS] "Missed" DIGITAL-INPUT-K changes ?
> > >
> > > Hi all,
> > > Has anyone ever seen ECS "miss" a change on
> > > a DIGITAL-INPUT-K Item (OCELOT/SECU-16) ?
> > > A potential customer is reporting such a problem
> > > with a PIR that opens the contact "briefly".
> > > Thanks,
> > > --
> > > Mark Gilmore
> > > Omnipotence (ECS home automation software)
> > > http://omnipotencesoftware.com
> > > 423-745-0026
> > > Hours: Mon-Sat, 9AM-8PM/EST

---

["text/x-vcard" not shown]

---