Subject: From: Date:

RE: [ECS] micro-redac and relays Mark Sekelsky Mon, 28 Dec 1998 21:30:10 -0600

---

David,

First, thanks so much for all your help.  Second I am apparently still doing
something wrong.

My Redac has the 8 relays and the 8 analogs across the top of the unit.
These are so labeled.  The screw posts along the bottom are not labeled and
I assume these are the digital inputs.  I ran wire to the basement (where my
system is) from the transformer.  I am using some phone cable I had laying
around if that matters.  I hook 1 end up to the screw post labeled "1" and
the other to either "9" or "10" (the two grounds).  I set up an item in item
editor.

When I first create an item in a group window it shows the item (let's call
it "digital") as being "high."  I would think this is correct (the initial
state is set to 'none').  When I apply power by turning the receiver ON the
item (in the group window) begins to toggle back and forth between  "low"
and "high."  Reversing the wires on the Redac doesn't help.  In fact with NO
connections to the Redac the item still toggles back and forth. I assume
that I am missing something silly? (the good news is that the Powerflash is
MUCH more reliable in it's new location).

Mark S

-----Original Message-----
From: David Mccoll [mailto:dmccoll@intergate.bc.ca]
Sent: Monday, December 28, 1998 4:10 PM
To: Mark@sekelsky.com
Subject: Re: [ECS] micro-redac and relays


Simply connect the positive of your power (transformer) supply that is
plugged into your receiver to a numbered input 0-7 on the Redac and the
negative to the G connection which stands for Ground. There are 2 grounds
and the 8 connections that correspond to the digital inputs.

After you have it all tested add the fuse and current limiting resistor.



-----Original Message-----
From: Mark Sekelsky <Mark@sekelsky.com>
To: dmccoll@intergate.bc.ca <dmccoll@intergate.bc.ca>
Date: Sunday, December 27, 1998 3:08 PM
Subject: RE: [ECS] micro-redac and relays


>There are 10 posts.  On the redac they are numbered 0-7 then GG.  On the
>posts themselves they are numbered 1-10.  Each post is the screw type where
>you tighten a screw to hold the wire (like on a breaker).
>
>Mark S
>
>-----Original Message-----
>From: David Mccoll [mailto:dmccoll@intergate.bc.ca]
>Sent: Sunday, December 27, 1998 1:57 PM
>To: ecs-list@netbloc.com
>Subject: Re: [ECS] micro-redac and relays
>
>
>Yup that's pretty much it. Inline fuse, inline resistor, attach to the
>Redac, and setup an item in ECS.
>
>Try to describe the physical connections to the digital inputs. Could you
>fire me off the .TXT file ?
>
>
>
>-----Original Message-----
>From: Mark Sekelsky <Mark@sekelsky.com>
>To: ecs-list@netbloc.com <ecs-list@netbloc.com>
>Date: Saturday, December 26, 1998 1:38 PM
>Subject: Re: [ECS] micro-redac and relays
>
>
>>David,
>>
>>I am no sure but I beleive my redac is an 8x8.  It will be three years old
>>in March.  It has 8 relay outputs, 8 analog inputs and 8 digital inputs.
I
>>didn't get any documnetation with it.  The disk that came with it does
have
>>a small .txt file but not what I would call a manual.
>>
>>If I understadn your message properly (and you which unit I have) it
sounds
>>like I just need to go to Radio Shack and pickup an in-line fuse then
>attach
>>the transformer directly to the redac in a similar fashion to the
>>Powerflash?
>>
>>Mark S
>>-----Original Message-----
>>From: David Mccoll <dmccoll@intergate.bc.ca>
>>To: ecs-list@netbloc.com <ecs-list@netbloc.com>
>>Date: Saturday, December 26, 1998 2:55 PM
>>Subject: Re: [ECS] micro-redac and relays
>>
>>
>>>Connect your transformers + lead to the numbered connector on the Redacs
>>>digital inputs and the - lead to the common or unmarked connector instead
>>of
>>>the Powerflash unit.
>>>
>>>When you accomplish this I would suggest you fuse and current limit the
>>>inputs as I posted earlier. It would be a big help to know more about
your
>>>Redac as there are a few models.
>>>
>>>You are right about the Powerflash units. They are not 100% and then you
>>>have to put up with the X-10 transmission delays.
>>>
>>>If in doubt just ask.
>>>Good luck.
>>>
>>>
>>>-----Original Message-----
>>>From: Mark Sekelsky <Mark@sekelsky.com>
>>>To: ecs-list@netbloc.com <ecs-list@netbloc.com>
>>>Date: Saturday, December 26, 1998 10:01 AM
>>>Subject: RE: [ECS] micro-redac and relays
>>>
>>>
>>>>Thanks to all who responded to my post about relays and the micro-redac.
>>>>This sounds like it is not quite as straight forward as I had thought.
>>Let
>>>>me throw something different out.  Currently I try and accomplish my
>>>>objective of determining the on/off state of the receiver via a
>Powerflash
>>>>module.  I have a transformer plugged into the back of the receiver
>(which
>>>>is always hot is the receiver is on) and the Powerflash wired to the
>>>>transformer.  The transformer is:
>>>>
>>>>Class 2
>>>>input 120v 60HZ 3.5w
>>>>output 5V DC 150ma
>>>>
>>>>The problem with this setup is that it is not 100% reliable (which
drives
>>>my
>>>>wife nuts).  When you apply power to the receiver the Powerflash sends a
>>>>signal (as determined by the light on tow separate TW253s) but ECS will
>>not
>>>>always ID the state change.  My Powerflash setting are Input 1 Mode 3.
>>>>
>>>>Perhaps I am using the wrong transformer or Powerflash settings?
>>>>
>>>>Mark S
>>>>
>>>>
>>>>
>>>
>>>
>>
>>
>
>

---