ecsl@netbloc.com: 4645: RE: [ECS] IR Master Model 100S

Subject:
From:
Date:

RE: [ECS] IR Master Model 100S
Steven M. Eaton
Sun, 27 Jun 1999 13:17:33 -0500

Sun, 27 Jun 1999 13:17:33 -0500

Thanks Mark and Garnet for the replies. It appears that a fluorescent light
I was using was causing my problems. I have been running for several days
now with no problems. Help that people on this list provide along with the
support from Mark, is invaluable when you have a problem that you have been
unable to solve. Once again, THANKS!

Steven M. Eaton
se3900@flash.net

-----Original Message-----
From: gbailey [mailto:gbailey@attcanada.net]
Sent: Wednesday, June 23, 1999 6:03 PM
To: ecs-list@netbloc.com
Subject: RE: [ECS] IR Master Model 100S

Make sure your com ports are set up correctly and no interrupt conflicts
exist. It should not be easy to lock it up. There have been instances of
flourescent and some of the newer "green" lights emitting some IR radiation
that can cause problems by flooding the receiver. Also, make sure to try the
other model settings as well.

-------------------------------------------------------------------
Garnet Bailey              gbailey@attcanada.net
                          www.attcanada.net/~gbailey
-------------------------------------------------------------------

-----Original Message-----
From: Steven M. Eaton [mailto:se3900@flash.net]
Sent: Wednesday, June 23, 1999 1:13 PM
To: Ecs-List
Subject: [ECS] IR Master Model 100S
I have a Dancraft IR Master Model 100S. I purchased this back in Feb./Mar.
time frame. I have it working but have been experiencing where the unit will
lockup at times when ir commands are sent. Then you have to power the unit
off and back on before it will start working again with ECS. I have
relearned the ir commands that I have defined several times, tried changing
the signal delay, and changing the buffer size as well even though I am
sending only one command when it locks up. It t does this on various
commands, and not just one. I was wondering if any of you that are using the
Model 100S are experiencing any problems like this and if not, what do you
have as the model under ECS? Are there any other suggestions that I could
try to correct this problem? I have tried the model 100 and the 100X, but
experience the lockups. Any help would be greatly appreciated.

Thanks Mark and Garnet for the replies. It appears that a fluorescent light I was using was causing my problems. I have been running for several days now with no problems. Help that people on this list provide along with the support from Mark, is invaluable when you have a problem that you have been unable to solve. Once again, THANKS!

Steven M. Eaton

se3900@flash.net

-----Original Message-----
From: gbailey [mailto:gbailey@attcanada.net]
Sent: Wednesday, June 23, 1999 6:03 PM
To: ecs-list@netbloc.com
Subject: RE: [ECS] IR Master Model 100S

Make sure your com ports are set up correctly and no interrupt conflicts exist. It should not be easy to lock it up. There have been instances of flourescent and some of the newer "green" lights emitting some IR radiation that can cause problems by flooding the receiver. Also, make sure to try the other model settings as well.

-------------------------------------------------------------------
Garnet Bailey gbailey@attcanada.net
www.attcanada.net/~gbailey
-------------------------------------------------------------------

-----Original Message-----
From: Steven M. Eaton [mailto:se3900@flash.net]
Sent: Wednesday, June 23, 1999 1:13 PM
To: Ecs-List
Subject: [ECS] IR Master Model 100S

I have a Dancraft IR Master Model 100S. I purchased this back in Feb./Mar. time frame. I have it working but have been experiencing where the unit will lockup at times when ir commands are sent. Then you have to power the unit off and back on before it will start working again with ECS. I have relearned the ir commands that I have defined several times, tried changing the signal delay, and changing the buffer size as well even though I am sending only one command when it locks up. It t does this on various commands, and not just one. I was wondering if any of you that are using the Model 100S are experiencing any problems like this and if not, what do you have as the model under ECS? Are there any other suggestions that I could try to correct this problem? I have tried the model 100 and the 100X, but experience the lockups. Any help would be greatly appreciated.