Subject: From: Date:

Re: [ECS] New TV-Guide Mark Gilmore Fri, 25 Aug 2000 14:14:24 -0400

---

Mark
ITPCST.DEF should reflect all your channels,
and this should have been initially done when
you setup TVL (per ECS.HTM).
See the TV-CHAN Type in the ITPCST.DEF.
-- 
Mark Gilmore
Omnipotence (ECS home automation software)
http://www.usit.com/omnip
423-745-0026
Hours: Mon-Sat, 9AM-8PM/EST


Mark Sekelsky wrote:
> 
> I checked my .chn file and made some updates.  I did not do anything to
> itpcst.def and never have.  Should I be editing this file to agree with
> .chn? For both of these files do I put spaces or tabs between the channel
> number and the station?
> 
> -----Original Message-----
> From: Mark Gilmore [mailto:omnip@usit.net]
> Sent: Thursday, August 24, 2000 6:41 AM
> To: ecs-list@netbloc.com
> Subject: Re: [ECS] New TV-Guide
> 
> Mark,
> Check your {lineup}.CHN file & ITPCST.DEF files.
> There are probably some new channels which one
> or both of these files lack (add as needed).
> --
> Mark Gilmore
> Omnipotence (ECS home automation software)
> http://www.usit.com/omnip
> 423-745-0026
> Hours: Mon-Sat, 9AM-8PM/EST
> 
> Mark Sekelsky wrote:
> >
> > Thanks Mark, it works great.  I do have one problem that I haven't figured
> > out.  Anytime I "click" on a listing with a channel over 40 I get an error
> > message that that number is an invalid selection.  As best I can tell all
> > other numbers work just fine.
> >
> > I copied and pasted the channel setting event from example.cfg.  I did
> have
> > to modify the actual sending of the signal to conform to my Home Vision.
> As
> > numbers 02-09 are all OK I know that isn't the problem.
> >
> > -----Original Message-----
> > From: Mark Gilmore [mailto:omnip@usit.net]
> > Sent: Tuesday, August 22, 2000 7:59 PM
> > To: ecs-list@netbloc.com
> > Subject: Re: [ECS] New TV-Guide
> >
> > Hi Mark,
> > I'll look at this tommorow, and will make ECS return
> > ANY requested page IF an empty password is defined which
> > applies to the requesting IP address (if not already).
> > --
> > Mark Gilmore
> > Omnipotence (ECS home automation software)
> > http://www.usit.com/omnip
> > 423-745-0026
> > Hours: Mon-Sat, 9AM-8PM/EST
> >
> > Mark Sekelsky wrote:
> > >
> > > I am trying to make use of the nifty new tv-guide.  ECS runs on a PC in
> my
> > > basement.  The main TV is up in the family room where I have another PC
> > > running ACE.  What I want to be able to do is to bring up the
> tv-guide.htm
> > > on that PC and have ECS set the TV stations.  From what I can tell so
> far
> > if
> > > I bring up tv-guide.htm directly I canNOT use it to have ECS set the
> > > station.  It seems like I have to navigate to the TV Guide page via
> > main.htm
> > > first.
> > >
> > > Is this correct and if so is there a way to run tv-guide.htm directly?
> > (ex.
> > > launch http://192.168.1.1:3000/tv-guide.htm)
> > >
> > > Mark S

---