Subject: From: Date:

Fw: [ECS] [Fwd: [ECS] AD "Bobcat" Modules] Tom Hutchins Wed, 27 Sep 2000 20:48:13 -0400

---

One other thing, on the CPUXA list the current threads indicate that if you
are setting up a new install and want to have the LEOPARD then there is no
reason to have an OCELOT unless you want an additional IR reciever point in
a separate room from the LEOPARD(basically the internal smarts of the extra
OCELOT would be wasted).
 Hope that helps.

Tom
----- Original Message -----
From: "Tom Hutchins" <thutchins@cinci.rr.com>
To: <ecs-list@netbloc.com>
Sent: Wednesday, September 27, 2000 8:41 PM
Subject: Re: [ECS] [Fwd: [ECS] AD "Bobcat" Modules]


> Mark,
>
> Sorry about that. I "assumed" that we were on the same page. My
> understanding from the CPUXA list is that the Leopard is simply an OCELOT
> with a touch screen. You use the same CMAX software for both and there is
no
> "special" coding for the Leopard other than for the touchscreen.
>
> Tom
> ----- Original Message -----
> From: "Mark Gilmore" <omnip@usit.net>
> To: <ecs-list@netbloc.com>
> Sent: Wednesday, September 27, 2000 7:05 PM
> Subject: Re: [ECS] [Fwd: [ECS] AD "Bobcat" Modules]
>
>
> > Yes - this is CRITICAL information.
> > I don't know if this will work at all,
> > as this is not a supported configuration.
> > And I know it won't work unless the Leopard
> > acts exactly like the Ocelot.
> > --
> > Mark Gilmore
> > Omnipotence (ECS home automation software)
> > http://omnipotencesoftware.com
> > 423-745-0026
> > Hours: Mon-Sat, 9AM-8PM/EST
> >
> >
> > Tom Hutchins wrote:
> > >
> > > Mark,
> > >
> > > There is no OCELOT. The Leopard is acting as the OCELOT as well as the
> > > touchscreen, (has the touchscreen interface with the guts of the
OCELOT)
> and
> > > the Leopard is the only thing attached to the computer!
> > >
> > > Does that help?
> > >
> > > Tom
> > > ----- Original Message -----
> > > From: "Mark Gilmore" <omnip@usit.net>
> > > To: <ecs-list@netbloc.com>
> > > Sent: Wednesday, September 27, 2000 6:51 PM
> > > Subject: Re: [ECS] [Fwd: [ECS] AD "Bobcat" Modules]
> > >
> > > > Tom,
> > > > Do you have any OTHER kinds of modules ?
> > > > Perhaps your Ocelot firmware is too old
> > > > to recognize the Leopard (??).
> > > > --
> > > > Mark Gilmore
> > > > Omnipotence (ECS home automation software)
> > > > http://omnipotencesoftware.com
> > > > 423-745-0026
> > > > Hours: Mon-Sat, 9AM-8PM/EST
> > > >
> > > >
> > > > Tom Hutchins wrote:
> > > > >
> > > > > Bob,
> > > > >
> > > > > I have the Leopard working fine using CMAX. However, CMAX doesn't
> have
> > > near
> > > > > the ease of use as ECS. I don't have any other modules hooked up
yet
> as
> > > I
> > > > > prefer to make sure each thing is working properly before I add
the
> next
> > > > > item. Sure makes troubleshooting easier.
> > > > >
> > > > > Tom
> > > > >
> > > > > ----- Original Message -----
> > > > > From: <bob.terfruchte@amd.com>
> > > > > To: <ecs-list@netbloc.com>
> > > > > Sent: Wednesday, September 27, 2000 6:34 PM
> > > > > Subject: RE: [ECS] [Fwd: [ECS] AD "Bobcat" Modules]
> > > > >
> > > > > > Tom,
> > > > > >
> > > > > > Can you "find" the modules with the C-Max software from ADI??
> > > > > >
> > > > > > Bob Terfruchte, Jr.
> > > > > > Austin, TX
> > > > > >
> > > > > > -----Original Message-----
> > > > > > From: Mark Gilmore [mailto:omnip@usit.net]
> > > > > > Sent: Wednesday, September 27, 2000 5:29 PM
> > > > > > To: ecs-list@netbloc.com
> > > > > > Subject: Re: [ECS] [Fwd: [ECS] AD "Bobcat" Modules]
> > > > > >
> > > > > >
> > > > > > Tom,
> > > > > > As I suspected, your dump shows that the OCELOT is
> > > > > > reporting NO modules of any kind. You might want to
> > > > > > call ADI on this (the 254's signify "no module"):
> > > > > >
> > > > > > Transmit ("get unit types" command):
> > > > > > 42 0 0 1 176 0 148 39
> > > > > >
> > > > > > Received:              1st 2nd 3rd ...
> > > > > > 42 0 0 1 176 0 254 254 254 254 254 254 254 254 254 254 254 254
> > > > > > 254 254 254 254 254 254 254 254 254 254 254 254 254 254 254 254
> > > > > > ....
> > > > > > --
> > > > > > Mark Gilmore
> > > > > > Omnipotence (ECS home automation software)
> > > > > > http://omnipotencesoftware.com
> > > > > > 423-745-0026
> > > > > > Hours: Mon-Sat, 9AM-8PM/EST
>

---